Init code
From SNESdev Wiki
Jump to navigationJump to search
When the SNES is powered on or reset, the 65c816 will jump to the RESET CPU vector (in bank 0) in 65C02 emulation mode.
At minimum, the Reset Handler should do the following:
- Preform a long jump into a FastROM bank (if the ROM speed is FastROM)
- Disable the emulation flag (switch to 65816 native mode)
- Setup the status flags. Specifically the register size flags, decimal mode flag (cleared) and irq disable flag (set).
- Setup the Stack Pointer
- Setup the Direct Page and Data Bank registers
- Disable interrupts and rendering
Afterwords, it is recommended you:
- Clear Work-RAM using multiple fixed address DMA transfers to WMDATA. The code should be inside the Reset Handler, not inside a subroutine and before any subroutines are called as the DMA transfers would override the stack. Ensure the DMA transfers do not override any memory you would like to survive a reset (ie, high-scores).
- Reset the PPU registers to a known good state
- Clear VRAM with a fixed address DMA transfer
- Clear CGRAM with a fixed address DMA transfer
- Populate OAM with values that will ensure all sprites are off-screen
- Jump to Main
Sample implementation:
ResetHandler:
jml _FastRomReset ; Change Program Bank to a FastROM bank
_FastRomReset:
clc
xce ; Switch to native mode
; Reset Status Flags
; n (negative flag) clear
; v (overflow flag) clear
; m (memory size) set - 8 bit Accumulator
; x (index size) clear - 16 bit Index registers
; d (decimal mode) clear - decimal mode disabled
; i (irq disable) set - IRQ interrupts disabled
; z (zero flag) clear
; c (carry flag) clear
rep #$ff
sep #$24
; 8 bit accumulator
; 16 bit index
ldx #STACK_BOTTOM
txs ; Set up Stack Pointer
pea 0
pld ; Reset Direct Page register to 0
phk
plb ; Set Data Bank to Program Bank
; addr addressing mode can now access PPU/MMIO/DMA registers if PB is $00 - $3F or $80 - $BF
stz NMITIMEN ; Disable interrupts
stz HDMAEN ; Disable HDMA
lda #$8f
sta INIDISP ; Disable screen
; Fill Work-RAM with zeros using two 64KiB fixed address DMA transfers to WMDATA
stz WMADDL
stz WMADDM
stz WMADDH ; Set VMDATA address
lda #$08
sta DMAP0 ; Fixed address transfer to a byte register
lda #WMDATA & $ff
sta BBAD0 ; DMA transfer to WMDATA
ldx #.loword(WorkRamResetByte)
stx A1T0
lda #.bankbyte(WorkRamResetByte)
sta A1B0 ; Set DMA source to `WorkRamResetByte`
ldx #0
stx DAS0 ; Transfer size = 64KiB
lda #1
sta MDMAEN ; First DMA Transfer
; x = 0
stx DAS0 ; Transfer size = 64KiB
; a = 1
sta MDMAEN ; Second DMA Transfer
; Reset PPU
jsr ResetRegisters
jsr ClearVRAM
jsr ClearCGRAM
jsr ResetOAM
jml Main ; Jump to Main
; Byte value to use when clearing Work-RAM
; (can be moved to any ROM bank)
WorkRamResetByte:
db 0
Reset Registers Routine
As the console lacks a boot ROM and most of the PPU registers start in an unknown state, the programmer will need to create a Reset Registers routine. This routine should be separate from the Reset Handler code to allow the programmer to reset the PPU registers to a known good state at the start of every level or scene.
The first registers to reset should be the NMITIMEN and HDMAEN registers. This will prevent Interrupts or HDMA from erroneously changing the PPU registers in the middle of the routine.
The following is a recommended list of registers to reset along with the values to reset them to.
Must reset first
NMITIMEN $4200 = 0 (disable Interrupts)
HDMAEN $420C = 0 (disable HDMA)
INIDISP $2100 = $8F (enable Force Blank, full brightness)
CPU registers
MEMSEL $420D = 0 (set to 1 if FastROM)
WRIO $4201 = $FF
Objects
OBJSEL $2101 = 0
OAMADDL $2102 = 0
OAMADDH $2103 = 0 (disable OAM priority rotation)
Backgrounds
BGMODE $2105 = 0
MOSAIC $2106 = 0
BG1SC $2107 = 0
BG2SC $2108 = 0
BG3SC $2109 = 0
BG4SC $210A = 0
BG12NBA $210B = 0
BG34NBA $210C = 0
Scroll Registers
BG1HOFS $210D = 0
BG1HOFS $210D = 0 (set horizontal offset to 0)
BG1VOFS $210E = $FF
BG1VOFS $210E = $FF (set vertical offset to -1)
BG2HOFS $210F = 0
BG2HOFS $210F = 0
BG2VOFS $2110 = $FF
BG2VOFS $2110 = $FF
BG3HOFS $2111 = 0
BG3HOFS $2111 = 0
BG3VOFS $2112 = $FF
BG3VOFS $2112 = $FF
BG4HOFS $2113 = 0
BG4HOFS $2113 = 0
BG4VOFS $2114 = $FF
BG4VOFS $2114 = $FF
VRAM Registers
VMAIN $2115 = $80 (VRAM word access, increment by 1, no remapping)
Mode 7
M7SEL $211A = 0 (no flipping or screen repeat)
M7A $211B = 0
M7A $211B = $01
M7B $211C = 0
M7B $211C = 0
M7C $211D = 0
M7C $211D = 0
M7D $211E = 0
M7D $211E = $01
M7X $211F = 0
M7X $211F = 0
M7Y $2120 = 0
M7Y $2120 = 0
Windows
W12SEL $2123 = 0
W34SEL $2124 = 0
WOBJSEL $2125 = 0
WH0 $2126 = 0
WH1 $2127 = 0
WH2 $2128 = 0
WH3 $2129 = 0
WBGLOG $212A = 0
WOBJLOG $212B = 0
Layer Enable
TM $212C = 0
TS $212D = 0
TMW $212E = 0
TSW $212F = 0
Color Math
CGWSEL $2130 = $30 (Color math disable region = everywhere)
CGADSUB $2131 = 0
COLDATA $2132 = $E0 (set Fixed color data to black)
Misc
SETINI $2133 = 0
References
- SNES Development Manual Book 1, section 2-26-1: Register Clear (Initial Settings)
